Balancers

HT pH/Alkalinity Increaser raised both pH and Alkalinity. With the use of spa test strips make certain to maintain your alkalinity between 80 to 150 ppm and your pH between 7.2 to 7.8 ppm. RECOMMENDED USE 1. Determine amount of add: If pH is between 6.8 to 7.2 add 1 oz. If pH is less than 6.8 add 2 ounces. 2. Turn OFF all pumps and blowers 3. Add pH/Alkalinity to spa water 4. Turn on filtration pump for 1 to 3 hours 5. Retest water after 3 hours 6. If pH is below 7.2 repeat procedure

Read more less

Water hardness levels should always be maintained between 200 to 400 ppm. Improper hardness levels can cause corrosion to your equipment and the spa surface. A primary indicator of low levels of hardness is foaming in the water. Liquid Calcium is simple to use and includes an especially high concentrate that adds convenience and savings. Example: to raise the hardness of 500 gallons of water just 20 ppm with Liquid Calcium requires only 3 oz verses 8 oz with almost all traditional competitor products. The most accurate measurement of water hardness is AquaChek Total Hardness Test Strips that provides readings between 0 to 1000 ppm. HT uses a high concentrate to save you money and add convenience because calcium increasers are limited to only allowing you to add a maximum of 3 oz at one time in hot water. After 3 oz you have to wait 30 minutes before adding more calcium increaser. A five minute treatment with HT becomes an afternoon event with most competitor products. RECOMMENDED USE Test your water with the use of AquaChek Total Hardness Test Strips. Add 1 oz per 7 ppm of increase required, not to exceed 3 oz if the water is warm. In cold water you can add up to 12 oz at one time. NOTE: There are no products on the market that will lower hardness levels. The only choices available are drain 12_ of your water and refill with soft water and retest results or call for delivered water making certain their water hardness levels are 400 ppm or less. If you have hard water make certain to use both Stain & Scale and Protections Plus along with keeping your ph in line. This will help prevent scaling.

Read more less

HT pH Hold & H2O Softener helps keep your spa water within the proper pH level reducing the need for constant adjustments. It also softens the water which is ideal for those with dry skin. Softening the water reduces the itchy feeling some bathers feel when exiting their spa, along with minimizing eye irritation and helping to prevent corrosion to your spa components. The compounds within the product are also reflective which adds a more sparkling look to your water.

Read more less

HT pH/Alkalinity Increaser raised both pH and Alkalinity. With the use of spa test strips make certain to maintain your alkalinity between 80 to 150 ppm and your pH between 7.2 to 7.8 ppm. RECOMMENDED USE 1. Determine amount of add: If pH is between 6.8 to 7.2 add 1 oz. If pH is less than 6.8 add 2 ounces. 2. Turn OFF all pumps and blowers 3. Add pH/Alkalinity to spa water 4. Turn on filtration pump for 1 to 3 hours 5. Retest water after 3 hours 6. If pH is below 7.2 repeat procedure

Read more less

HT pH/Alkalinity Down lowers both pH and Alkalinity. With the use of spa test strips make certain to maintain your alkalinity between 80 to 150 ppm and your pH between 7.2 to 7.8 ppm. Important to use whenever pH climbs above 7.8 ppm! RECOMMENDED USE 1. Turn OFF all pumps and blowers 2. Add _ oz (1 _ tsp) for every 500 gallons NOTE: For best results add granular to small bucket of water then pour into spa 3. Turn on filtration pump for 30 minutes 4. Test and repeat procedure is pH is above 7.8 ppm

Read more less