Chemicals

HT Spa Activator is an odorless shock that is the most favored product by hot tub owners whether they use chlorine or bromine. It is a powerful oxidizer formulated to be safe to use after each use of the hot tub whether you are using chlorine, bromine, or mineral purifiers. HT Spa Activator is a shock not a sanitizer and is extremely effective in eliminating organic contaminants introduced by bathers such as body oils, lotions, urine, etc. along with environmental factors like rain and wind. Essentially it allows sanitizers to more be effective in eliminating bacteria and viruses along with reducing the frequency of adding sanitizers in order to keep a proper ppm level. Best of all it contains no chlorine, unlike bromine, so it is essentially odorless. RECOMMENDED USE Add 2 ounces per 300 gallons of water each time you exit your spa or 2 ounces weekly if the spa has not been used. Make certain filtration pump is active for at least 30 minutes each time you add Spa Activator.

Read more less

HT Stain & Scale is a very effective in inhibiting the formation of rusty, green, brown, or cloudy water. This discoloration is primarily due from the presence of metallic or mineral impurities, such as copper, iron, and manganese salts in your water supply or the result of corrosive action of acidic water (low pH). Warning: excessive scaling within your water could cause corrosion of your heating element and discoloration of the spa acrylic surface. Proper use of Stain & Scale in cooperation with Protection Plus protects your spa and equipment. RECOMMENDED USE: Each time you refill your spa add 16 oz of HT Stain & Scale on spas up to 500 gallons. Stain & Scale should be added while you are filling the spa. Within 24 hours of adding the 16 oz of Stain & Scale you should remove and clean your filter cartridges. For spas with high concentration of minerals or those showing signs of rusty water or scaling be sure to follow a maintenance program of adding 1 oz of Stain & Scale per each 100 gallons of water each week.

Read more less

HT Mineral Stick contains a mineral formula that destroys bacteria while neutralizing acids, which helps keep the pH in an acceptable range with less monitoring and assists in keeping your water crystal clear. Using the HT Mineral Stick helps reduce required levels of bromine or chlorine, improves spa pleasure by reducing the problems associated with bromine or chlorine, including faded bathing suits, premature damage to spa equipment or surfaces and smelly odors. Works on spas up to 600 gallons and requires replacement every 4 months, depending upon usage. RECOMMENDED USE Simply place in the spas skimmer basket and replace every 4 months. Should be used with bromine or chlorine and follow all directions for proper use of balancing and maintaining water quality.

Read more less

HT Chemicals uses the highest concentrate available on the market: 99% Sodium Dichloro and 55.5% Available Chlorine. Unlike many competitors our chemicals are produced and packaged in the USA, guaranteed to be fresh. Our Chlorine contains no scale forming minerals, dissolves instantly and is specifically formulated for warm water use in hot tubs! RECOMMENDED USE With pump on, add 1 teaspoon per 200 gallons of water on initial treatment. Repeat every 15 minutes if necessary to reach a 3 to 5 ppm of available chlorine. Use test strips to maintain 3 to 5 ppm reading. After each usage of spa it is recommended to add 2 ounces of HT Spa Activator (per 300 gallons of water) to shock and treat the water. Spa Activator does not raise yourMaintain 3 to 5 ppm of chorine and add HT Spa Activator weekly even when spa is not in use.

Read more less

HT pH/Alkalinity Increaser raised both pH and Alkalinity. With the use of spa test strips make certain to maintain your alkalinity between 80 to 150 ppm and your pH between 7.2 to 7.8 ppm. RECOMMENDED USE 1. Determine amount of add: If pH is between 6.8 to 7.2 add 1 oz. If pH is less than 6.8 add 2 ounces. 2. Turn OFF all pumps and blowers 3. Add pH/Alkalinity to spa water 4. Turn on filtration pump for 1 to 3 hours 5. Retest water after 3 hours 6. If pH is below 7.2 repeat procedure

Read more less

Over time, even a well maintained spa or jetted bathtub will accumulate unseen, bacteria breeding deposits in the plumbing lines. While chemicals keep your spa water clean, they are ineffective in dissolving dirt, soap, and mineral deposits hidden within your plumbing. HT Jet Line Cleaner rids your plumbing lines of bacteria but unlike other less advanced formulas it is effective in cleaning jet bodies and does not require you to drain and fill your spa twice. Using Jet Line Cleaner each time you drain and fill your hot tub will help protect your pump seals and heater element. RECOMMENDED USE 1. Remove and clean filter and keep outside of spa 2. Before you drain your spa add 16 oz. of Jet Line Cleaner to warm water 3. With filter out, turn pump(s) on and run jets for 15 minutes 4. Turn pump(s) off and let it sit for 1 hour 5. Drain spa and while draining hose off all side walls 6. Refill spa according to directions NOTE: Some residual foaming may occur. If so, use foam away to suppress. For Jetted bathtubs holding less than 15 gallons use 8 oz.

Read more less

This is an enhanced formula, unlike other competitive products on the market. Keep out of reach of children and avoid splashing it on surfaces such as linoleum or tile. The use of HT Filter Cleaner will effectively break down the body oils, grease, soap film, calcium deposits, and other contaminates on your filter cartridge. The result will be an improved filter efficiency and an extended life to your cartridge. Regular use of this product will assure proper filtration. RECOMMENDED USE Mix 8 oz of Filter Cleaner per 1.25 gallons of clean water in a large plastic container that will hold enough water to cover the filter(s) you wish to soak. Always add Filter Cleaner to the water not the reverse and never use a metal container with Filter Cleaner. Place cartridge(s) fully immersed in the solution and allow 10 to 12 hours to soak. Remove cartridges and rinse thoroughly with clean water. Place on a shelf and allow cartridges to air dry before reinserting them into your spa. To avoid down time on your spa and to extend the life of your filter(s) it is recommended to have a spare set of filters. NOTE: Dirty filters restrict water flow and performance of your jets along with causing pumps to fail. You should clean your filters each time you change your water and once every two weeks clean them with Instant Cartridge Cleaner.

Read more less

The powerful oxygen-based oxidizer provides 2 benefits when used in conjunction with spa water sanitized by Chlorine. It helps eliminate contaminates introduced by bathers along with environmental factors like wind and rain. It also helps restore sparkle and clarity to the water without affecting hardness or stabiliser levels.Recommend using 1 ounce per every 100 gallons (3oz in a 300-gallon spa)

Read more less

Traditional Bromine Tablets are dissolving products that have a high percentage of chlorine and continue to emit a high scent. HT are non-dissolving, erosion based tablets that are extra hard and designed to work with HT Brom Bank a liquid bromide salt solution and HT Activator. Our products are simple to use, dramatically reduce the odor of chlorine in warm water hot tubs, and provide an improved sanitizing solution. Optimum range of active bromine residual is 2 to 5 ppm. RECOMMENDED USE On your initial fill add 1 ounce of HT Brom Bank per each 100 gallons of water to your spa. Install 3 Bromine Tablets per 300 gallons of spa water via the use of a Bromine Floating Dispenser. Adjust feeder to maintain a minimum of 2 ppm of active bromine residual. Maintain spa by adding no more than 3 tablets each time approximately every 5 to 7 days or as needed to maintain between 2 to 5 ppm. For additional sanitizing and to keep chlorine scent to a minimum add 2 ounce of HT Spa Activator after each use. HT Bromine Tablets can be used similar to traditional Tablets but not with the same effectiveness or benefits as prescribed within.

Read more less

Protection Plus is a concentrated stain and scale preventer in the spa and helps prevent calcium build up on acrylic spa surface, along with helping to keep your water crystal clear. RECOMMENDED USE Add 1 oz of Protection Plus once a week for proper maintenance and stain and scale prevention. For spas with any concentration of minerals it is recommended to add 16 oz of Stain & Scale each time you fill your spa with fresh water.

Read more less

Water hardness levels should always be maintained between 200 to 400 ppm. Improper hardness levels can cause corrosion to your equipment and the spa surface. A primary indicator of low levels of hardness is foaming in the water. Liquid Calcium is simple to use and includes an especially high concentrate that adds convenience and savings. Example: to raise the hardness of 500 gallons of water just 20 ppm with Liquid Calcium requires only 3 oz verses 8 oz with almost all traditional competitor products. The most accurate measurement of water hardness is AquaChek Total Hardness Test Strips that provides readings between 0 to 1000 ppm. HT uses a high concentrate to save you money and add convenience because calcium increasers are limited to only allowing you to add a maximum of 3 oz at one time in hot water. After 3 oz you have to wait 30 minutes before adding more calcium increaser. A five minute treatment with HT becomes an afternoon event with most competitor products. RECOMMENDED USE Test your water with the use of AquaChek Total Hardness Test Strips. Add 1 oz per 7 ppm of increase required, not to exceed 3 oz if the water is warm. In cold water you can add up to 12 oz at one time. NOTE: There are no products on the market that will lower hardness levels. The only choices available are drain 12_ of your water and refill with soft water and retest results or call for delivered water making certain their water hardness levels are 400 ppm or less. If you have hard water make certain to use both Stain & Scale and Protections Plus along with keeping your ph in line. This will help prevent scaling.

Read more less

HT Brom for Spas is a clear solution of Bromide Salts which remain in your spa water to activate and enhance the performance of our HT Bromine Tablets. Properly used with HT Bromide Tabs it immediately create pure bromine dramatically reducing the scent of chlorine found in all traditional bromine tablets. RECOMMENDED USE Add 2 ounces of Brom Bank to your spa on the initial fill before adding Bromine Tablets. Then after each use add 2 ounces of HT Spa Activator. For enhanced sanitation of your spa water simply add 2 ounces of Brom Bank every 1 to 2 weeks depending upon use.

Read more less

HT Natural & Clear is a natural enzyme that emulsifies and biodegrades organics (body oils, suntan lotion, etc.) as soon as they enter your spa helping to keep your water crystal clear with no discomfort to the spa user. By removing these organics Natural & Clear helps your sanitizer work more efficiently and reduces the amount of sanitizer required to maintain a proper ppm level. Natural & Clear also helps rid your spa of common scum lines caused by contaminants. NOTE: Most competitors sell Clarifiers that are coagulates that group small particles (less than 15 microns) together making them available for your filter to capture. These less expensive formulas are not natural enzymes, are less effective, and do not help rid your spa of scum lines.

Read more less

HT All Purpose Cleaner is specially formulated to easily remove stubborn deposits on acrylic spas and pool surfaces without altering the water chemistry, pH levels, or causing any foaming in the water. It is also ideal on faux wood spa cabinet panels, plastic steps, and even most outdoor furniture, boat, car, and bath products. Includes spray attachment. RECOMMENDED USE Simply spray and wipe clean. For stubborn deposits on the acrylic allow to sit for 5 minutes then scrub, rinse, and wipe clean. Recommended to be used with our spa scrubbing brushes. NOTE: This is an earth friendly, biodegradable product that contains no soap, detergent, alcohol, or phosphates.

Read more less

HT Instant Cartridge Cleaner quickly removes scum, oils, minerals, and scale from cartridge filters. This special liquid formula is a heavy concentrate that works in minutes, requires no scrubbing, and allows you to continue to enjoy your spa without delay. RECOMMENDED USE Simply remove the cartridge filter and rinse it thoroughly with a pressure activated garden hose. While wet, spray on Instant Cartridge Cleaner on the entire surface and allow 3 to 5 minutes to set. Rinse thoroughly and reinstall cartridge filters into spa. NOTE: Use of the Filter Flosser makes cleaning your filter easy and more effective. Approximately every 3 months thoroughly clean your filters by soaking them for 10 to 12 hours in Filter Clean solution. Proper care of your filters will save you money by extending their life. Remember: Dirty filters restrict water flow and performance of your jets along with causing pumps to fail. You should clean your filters each time you change your water and once every two weeks clean them with Instant Cartridge Cleaner.

Read more less

HT Cover Conditioner protects and extends the life of your cover. Exclusively formulated to effectively clean and restore the luster to vinyl and other hard surfaces. This unique product keeps the vinyl from hardening and cracking, particularly covers exposed to the harsh ultraviolet rays of the sun and other harmful outdoor elements. NOTE: Traditional household vinyl cleaners like Amoral will damage and discolor any cover vinyl skin, voiding your warranty.

Read more less

HT pH Hold & H2O Softener helps keep your spa water within the proper pH level reducing the need for constant adjustments. It also softens the water which is ideal for those with dry skin. Softening the water reduces the itchy feeling some bathers feel when exiting their spa, along with minimizing eye irritation and helping to prevent corrosion to your spa components. The compounds within the product are also reflective which adds a more sparkling look to your water.

Read more less

HT Spa Activator is an odorless shock that is the most favored product by hot tub owners whether they use chlorine or bromine. It is a powerful oxidizer formulated to be safe to use after each use of the hot tub whether you are using chlorine, bromine, or mineral purifiers. HT Spa Activator is a shock not a sanitizer and is extremely effective in eliminating organic contaminants introduced by bathers such as body oils, lotions, urine, etc. along with environmental factors like rain and wind. Essentially it allows sanitizers to more be effective in eliminating bacteria and viruses along with reducing the frequency of adding sanitizers in order to keep a proper ppm level. Best of all it contains no chlorine, unlike bromine, so it is essentially odorless. RECOMMENDED USE Add 2 ounces per 300 gallons of water each time you exit your spa or 2 ounces weekly if the spa has not been used. Make certain filtration pump is active for at least 30 minutes each time you add Spa Activator.

Read more less

HT pH/Alkalinity Increaser raised both pH and Alkalinity. With the use of spa test strips make certain to maintain your alkalinity between 80 to 150 ppm and your pH between 7.2 to 7.8 ppm. RECOMMENDED USE 1. Determine amount of add: If pH is between 6.8 to 7.2 add 1 oz. If pH is less than 6.8 add 2 ounces. 2. Turn OFF all pumps and blowers 3. Add pH/Alkalinity to spa water 4. Turn on filtration pump for 1 to 3 hours 5. Retest water after 3 hours 6. If pH is below 7.2 repeat procedure

Read more less

HT pH/Alkalinity Down lowers both pH and Alkalinity. With the use of spa test strips make certain to maintain your alkalinity between 80 to 150 ppm and your pH between 7.2 to 7.8 ppm. Important to use whenever pH climbs above 7.8 ppm! RECOMMENDED USE 1. Turn OFF all pumps and blowers 2. Add _ oz (1 _ tsp) for every 500 gallons NOTE: For best results add granular to small bucket of water then pour into spa 3. Turn on filtration pump for 30 minutes 4. Test and repeat procedure is pH is above 7.8 ppm

Read more less

HT Foam Away breaks up existing foam instantaneously in spas, hot tubs, and whirlpools. HT uses a specially formulated high concentration that requires so little to be effective that it can best be used with a spray applicator targeting only the foaming areas. RECOMMENDED USE To Prevent Foaming: shake well and disperse no more than a capful of Foam Away onto the surface of the water. To Eliminate when foaming occurs: shake well and disperse one capful where foaming exists or use a spray activator lightly on surface of water. If foaming persists after 30 minutes repeat procedure.

Read more less

HT Chemicals uses the highest concentrate available on the market: 99% Sodium Dichloro and 55.5% Available Chlorine. Unlike many competitors our chemicals are produced and packaged in the USA, guaranteed to be fresh. Our Chlorine contains no scale forming minerals, dissolves instantly and is specifically formulated for warm water use in hot tubs! RECOMMENDED USE With pump on, add 1 teaspoon per 200 gallons of water on initial treatment. Repeat every 15 minutes if necessary to reach a 3 to 5 ppm of available chlorine. Use test strips to maintain 3 to 5 ppm reading. After each usage of spa it is recommended to add 2 ounces of HT Spa Activator (per 300 gallons of water) to shock and treat the water. Spa Activator does not raise yourMaintain 3 to 5 ppm of chorine and add HT Spa Activator weekly even when spa is not in use.

Read more less